Brooklyn/arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts

/dts-v1/;

#include "bcm2710.dtsi"
#include "bcm2709-rpi.dtsi"
#include "bcm283x-rpi-lan7515.dtsi"
#include "bcm283x-rpi-csi1-2lane.dtsi"
#include "bcm283x-rpi-i2c0mux_0_44.dtsi"
#include "bcm271x-rpi-bt.dtsi"
#include "bcm283x-rpi-cam1-regulator.dtsi"

/ {
	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
	model = "Raspberry Pi 3 Model B+";

	chosen {
		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1";
	};

	aliases {
		serial0 = &uart1;
		serial1 = &uart0;
		mmc1 = &mmcnr;
	};
};

&gpio {
	spi0_pins: spi0_pins {
		brcm,pins = <9 10 11>;
		brcm,function = <4>; /* alt0 */
	};

	spi0_cs_pins: spi0_cs_pins {
		brcm,pins = <8 7>;
		brcm,function = <1>; /* output */
	};

	i2c0_pins: i2c0 {
		brcm,pins = <0 1>;
		brcm,function = <4>;
	};

	i2c1_pins: i2c1 {
		brcm,pins = <2 3>;
		brcm,function = <4>;
	};

	i2s_pins: i2s {
		brcm,pins = <18 19 20 21>;
		brcm,function = <4>; /* alt0 */
	};

	sdio_pins: sdio_pins {
		brcm,pins =     <34 35 36 37 38 39>;
		brcm,function = <7>; // alt3 = SD1
		brcm,pull =     <0 2 2 2 2 2>;
	};

	bt_pins: bt_pins {
		brcm,pins = <43>;
		brcm,function = <4>; /* alt0:GPCLK2 */
		brcm,pull = <0>;
	};

	uart0_pins: uart0_pins {
		brcm,pins = <32 33>;
		brcm,function = <7>; /* alt3=UART0 */
		brcm,pull = <0 2>;
	};

	uart1_pins: uart1_pins {
		brcm,pins;
		brcm,function;
		brcm,pull;
	};

	audio_pins: audio_pins {
		brcm,pins = <40 41>;
		brcm,function = <4>;
	};
};

&mmcnr {
	pinctrl-names = "default";
	pinctrl-0 = <&sdio_pins>;
	bus-width = <4>;
	status = "okay";
};

&firmware {
	expgpio: expgpio {
		compatible = "raspberrypi,firmware-gpio";
		gpio-controller;
		#gpio-cells = <2>;
		status = "okay";
	};
};

&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_pins &bt_pins>;
	status = "okay";
};

&uart1 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart1_pins>;
	status = "okay";
};

&spi0 {
	pinctrl-names = "default";
	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;

	spidev0: spidev@0{
		compatible = "spidev";
		reg = <0>;	/* CE0 */
		#address-cells = <1>;
		#size-cells = <0>;
		spi-max-frequency = <125000000>;
	};

	spidev1: spidev@1{
		compatible = "spidev";
		reg = <1>;	/* CE1 */
		#address-cells = <1>;
		#size-cells = <0>;
		spi-max-frequency = <125000000>;
	};
};

&i2c0if {
	clock-frequency = <100000>;
};

&i2c1 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_pins>;
	clock-frequency = <100000>;
};

&i2c2 {
	clock-frequency = <100000>;
};

&i2s {
	pinctrl-names = "default";
	pinctrl-0 = <&i2s_pins>;
};

&leds {
	act_led: led-act {
		label = "led0";
		linux,default-trigger = "mmc0";
		gpios = <&gpio 29 0>;
	};

	pwr_led: led-pwr {
		label = "led1";
		linux,default-trigger = "default-on";
		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
	};
};

&hdmi {
	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
};

&audio {
	pinctrl-names = "default";
	pinctrl-0 = <&audio_pins>;
};

&eth_phy {
	microchip,eee-enabled;
	microchip,tx-lpi-timer = <600>; /* non-aggressive*/
	microchip,downshift-after = <2>;
};

&cam1_reg {
	gpio = <&expgpio 5 GPIO_ACTIVE_HIGH>;
};

/ {
	__overrides__ {
		act_led_gpio = <&act_led>,"gpios:4";
		act_led_activelow = <&act_led>,"gpios:8";
		act_led_trigger = <&act_led>,"linux,default-trigger";

		pwr_led_gpio = <&pwr_led>,"gpios:4";
		pwr_led_activelow = <&pwr_led>,"gpios:8";
		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";

		eee = <&eth_phy>,"microchip,eee-enabled?";
		tx_lpi_timer = <&eth_phy>,"microchip,tx-lpi-timer:0";
		eth_led0 = <&eth_phy>,"microchip,led-modes:0";
		eth_led1 = <&eth_phy>,"microchip,led-modes:4";
		eth_downshift_after = <&eth_phy>,"microchip,downshift-after:0";
		eth_max_speed = <&eth_phy>,"max-speed:0";
	};
};