// Definitions for SX150x I2C GPIO Expanders from Semtech

// dtparams:
//     sx150<x>-<n>-<m>          - Enables SX150X device on I2C#<n> with slave address <m>. <x> may be 1-9.
//                                 <n> may be 0 or 1.  Permissible values of <m> (which is denoted in hex)
//                                 depend on the device variant.
//                                 For SX1501, SX1502, SX1504 and SX1505, <m> may be 20 or 21.
//                                 For SX1503 and SX1506, <m> may be 20.
//                                 For SX1507 and SX1509, <m> may be 3E, 3F, 70 or 71.
//                                 For SX1508, <m> may be 20, 21, 22 or 23.
//     sx150<x>-<n>-<m>-int-gpio - Integer, enables interrupts on SX150X device on I2C#<n> with slave address <m>,
//                                 specifies the GPIO pin to which NINT output of SX150X is connected.
//
//
// Example 1: A single SX1505 device on I2C#1 with its slave address set to 0x20 and NINT output connected to GPIO25:
// dtoverlay=sx150x:sx1505-1-20,sx1505-1-20-int-gpio=25
//
// Example 2: Two SX1507 devices on I2C#0 with their slave addresses set to 0x3E and 0x70 (interrupts not used):
// dtoverlay=sx150x:sx1507-0-3E,sx1507-0-70

/dts-v1/;
/plugin/;

/ {
	compatible = "brcm,bcm2835";

	// Enable I2C#0 interface
	fragment@0 {
		target = <&i2c0>;
		__dormant__ {
			status = "okay";
		};
	};

	// Enable I2C#1 interface
	fragment@1 {
		target = <&i2c1>;
		__dormant__ {
			status = "okay";
		};
	};

	// Enable a SX1501 on I2C#0 at slave addr 0x20
	fragment@2 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1501_0_20: sx150x@20 {
				compatible = "semtech,sx1501q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1501-0-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1501 on I2C#1 at slave addr 0x20
	fragment@3 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1501_1_20: sx150x@20 {
				compatible = "semtech,sx1501q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1501-1-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1501 on I2C#0 at slave addr 0x21
	fragment@4 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1501_0_21: sx150x@21 {
				compatible = "semtech,sx1501q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1501-0-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1501 on I2C#1 at slave addr 0x21
	fragment@5 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1501_1_21: sx150x@21 {
				compatible = "semtech,sx1501q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1501-1-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1502 on I2C#0 at slave addr 0x20
	fragment@6 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1502_0_20: sx150x@20 {
				compatible = "semtech,sx1502q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1502-0-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1502 on I2C#1 at slave addr 0x20
	fragment@7 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1502_1_20: sx150x@20 {
				compatible = "semtech,sx1502q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1502-1-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1502 on I2C#0 at slave addr 0x21
	fragment@8 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1502_0_21: sx150x@21 {
				compatible = "semtech,sx1502q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1502-0-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1502 on I2C#1 at slave addr 0x21
	fragment@9 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1502_1_21: sx150x@21 {
				compatible = "semtech,sx1502q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1501-1-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1503 on I2C#0 at slave addr 0x20
	fragment@10 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1503_0_20: sx150x@20 {
				compatible = "semtech,sx1503q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1503-0-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1503 on I2C#1 at slave addr 0x20
	fragment@11 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1503_1_20: sx150x@20 {
				compatible = "semtech,sx1503q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1503-1-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1504 on I2C#0 at slave addr 0x20
	fragment@12 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1504_0_20: sx150x@20 {
				compatible = "semtech,sx1504q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1504-0-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1504 on I2C#1 at slave addr 0x20
	fragment@13 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1504_1_20: sx150x@20 {
				compatible = "semtech,sx1504q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1504-1-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1504 on I2C#0 at slave addr 0x21
	fragment@14 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1504_0_21: sx150x@21 {
				compatible = "semtech,sx1504q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1504-0-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1504 on I2C#1 at slave addr 0x21
	fragment@15 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1504_1_21: sx150x@21 {
				compatible = "semtech,sx1504q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1504-1-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1505 on I2C#0 at slave addr 0x20
	fragment@16 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1505_0_20: sx150x@20 {
				compatible = "semtech,sx1505q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1505-0-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1505 on I2C#1 at slave addr 0x20
	fragment@17 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1505_1_20: sx150x@20 {
				compatible = "semtech,sx1505q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1505-1-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1505 on I2C#0 at slave addr 0x21
	fragment@18 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1505_0_21: sx150x@21 {
				compatible = "semtech,sx1505q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1505-0-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1505 on I2C#1 at slave addr 0x21
	fragment@19 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1505_1_21: sx150x@21 {
				compatible = "semtech,sx1505q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1505-1-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1506 on I2C#0 at slave addr 0x20
	fragment@20 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1506_0_20: sx150x@20 {
				compatible = "semtech,sx1506q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1506-0-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1506 on I2C#1 at slave addr 0x20
	fragment@21 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1506_1_20: sx150x@20 {
				compatible = "semtech,sx1506q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1506-1-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1507 on I2C#0 at slave addr 0x3E
	fragment@22 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1507_0_3E: sx150x@3E {
				compatible = "semtech,sx1507q";
				reg = <0x3E>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1507_0_3E-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1507 on I2C#1 at slave addr 0x3E
	fragment@23 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1507_1_3E: sx150x@3E {
				compatible = "semtech,sx1507q";
				reg = <0x3E>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1507_1_3E-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1507 on I2C#0 at slave addr 0x3F
	fragment@24 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1507_0_3F: sx150x@3F {
				compatible = "semtech,sx1507q";
				reg = <0x3F>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1507_0_3F-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1507 on I2C#1 at slave addr 0x3F
	fragment@25 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1507_1_3F: sx150x@3F {
				compatible = "semtech,sx1507q";
				reg = <0x3F>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1507_1_3F-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1507 on I2C#0 at slave addr 0x70
	fragment@26 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1507_0_70: sx150x@70 {
				compatible = "semtech,sx1507q";
				reg = <0x70>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1507-0-70-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1507 on I2C#1 at slave addr 0x70
	fragment@27 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1507_1_70: sx150x@70 {
				compatible = "semtech,sx1507q";
				reg = <0x70>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1507-1-70-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1507 on I2C#0 at slave addr 0x71
	fragment@28 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1507_0_71: sx150x@71 {
				compatible = "semtech,sx1507q";
				reg = <0x71>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1507-0-71-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1507 on I2C#1 at slave addr 0x71
	fragment@29 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1507_1_71: sx150x@71 {
				compatible = "semtech,sx1507q";
				reg = <0x71>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1507-1-71-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1508 on I2C#0 at slave addr 0x20
	fragment@30 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1508_0_20: sx150x@20 {
				compatible = "semtech,sx1508q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1508-0-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1508 on I2C#1 at slave addr 0x20
	fragment@31 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1508_1_20: sx150x@20 {
				compatible = "semtech,sx1508q";
				reg = <0x20>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1508-1-20-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1508 on I2C#0 at slave addr 0x21
	fragment@32 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1508_0_21: sx150x@21 {
				compatible = "semtech,sx1508q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1508-0-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1508 on I2C#1 at slave addr 0x21
	fragment@33 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1508_1_21: sx150x@21 {
				compatible = "semtech,sx1508q";
				reg = <0x21>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1508-1-21-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1508 on I2C#0 at slave addr 0x22
	fragment@34 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1508_0_22: sx150x@22 {
				compatible = "semtech,sx1508q";
				reg = <0x22>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1508-0-22-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1508 on I2C#1 at slave addr 0x22
	fragment@35 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1508_1_22: sx150x@22 {
				compatible = "semtech,sx1508q";
				reg = <0x22>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1508-1-22-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1508 on I2C#0 at slave addr 0x23
	fragment@36 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1508_0_23: sx150x@23 {
				compatible = "semtech,sx1508q";
				reg = <0x23>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1508-0-23-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1508 on I2C#1 at slave addr 0x23
	fragment@37 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1508_1_23: sx150x@23 {
				compatible = "semtech,sx1508q";
				reg = <0x23>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1508-1-23-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1509 on I2C#0 at slave addr 0x3E
	fragment@38 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1509_0_3E: sx150x@3E {
				compatible = "semtech,sx1509q";
				reg = <0x3E>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1509_0_3E-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1509 on I2C#1 at slave addr 0x3E
	fragment@39 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1509_1_3E: sx150x@3E {
				compatible = "semtech,sx1509q";
				reg = <0x3E>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1509_1_3E-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1509 on I2C#0 at slave addr 0x3F
	fragment@40 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1509_0_3F: sx150x@3F {
				compatible = "semtech,sx1509q";
				reg = <0x3F>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1509_0_3F-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1509 on I2C#1 at slave addr 0x3F
	fragment@41 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1509_1_3F: sx150x@3F {
				compatible = "semtech,sx1509q";
				reg = <0x3F>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1509_1_3F-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1509 on I2C#0 at slave addr 0x70
	fragment@42 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1509_0_70: sx150x@70 {
				compatible = "semtech,sx1509q";
				reg = <0x70>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1509-0-70-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1509 on I2C#1 at slave addr 0x70
	fragment@43 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1509_1_70: sx150x@70 {
				compatible = "semtech,sx1509q";
				reg = <0x70>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1509-1-70-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1509 on I2C#0 at slave addr 0x71
	fragment@44 {
		target = <&i2c0>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1509_0_71: sx150x@71 {
				compatible = "semtech,sx1509q";
				reg = <0x71>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1509-0-71-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable a SX1509 on I2C#1 at slave addr 0x71
	fragment@45 {
		target = <&i2c1>;
		__dormant__ {
			#address-cells = <1>;
			#size-cells = <0>;

			sx1509_1_71: sx150x@71 {
				compatible = "semtech,sx1509q";
				reg = <0x71>;
				gpio-controller;
				#gpio-cells = <2>;
				#interrupt-cells = <2>;
				interrupts = <25 2>; /* 1st word overwritten by sx1509-1-71-int-gpio parameter
				                        2nd word is 2 for falling-edge triggered */
				status = "okay";
			};
		};
	};

	// Enable interrupts for a SX1501 on I2C#0 at slave addr 0x20
	fragment@46 {
		target = <&sx1501_0_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_20_pins>;
		};
	};

	// Enable interrupts for a SX1501 on I2C#1 at slave addr 0x20
	fragment@47 {
		target = <&sx1501_1_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_20_pins>;
		};
	};

	// Enable interrupts for a SX1501 on I2C#0 at slave addr 0x21
	fragment@48 {
		target = <&sx1501_0_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_21_pins>;
		};
	};

	// Enable interrupts for a SX1501 on I2C#1 at slave addr 0x21
	fragment@49 {
		target = <&sx1501_1_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_21_pins>;
		};
	};

	// Enable interrupts for a SX1502 on I2C#0 at slave addr 0x20
	fragment@50 {
		target = <&sx1502_0_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_20_pins>;
		};
	};

	// Enable interrupts for a SX1502 on I2C#1 at slave addr 0x20
	fragment@51 {
		target = <&sx1502_1_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_20_pins>;
		};
	};

	// Enable interrupts for a SX1502 on I2C#0 at slave addr 0x21
	fragment@52 {
		target = <&sx1502_0_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_21_pins>;
		};
	};

	// Enable interrupts for a SX1502 on I2C#1 at slave addr 0x21
	fragment@53 {
		target = <&sx1502_1_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_21_pins>;
		};
	};

	// Enable interrupts for a SX1503 on I2C#0 at slave addr 0x20
	fragment@54 {
		target = <&sx1503_0_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_20_pins>;
		};
	};

	// Enable interrupts for a SX1503 on I2C#1 at slave addr 0x20
	fragment@55 {
		target = <&sx1503_1_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_20_pins>;
		};
	};

	// Enable interrupts for a SX1504 on I2C#0 at slave addr 0x20
	fragment@56 {
		target = <&sx1504_0_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_20_pins>;
		};
	};

	// Enable interrupts for a SX1504 on I2C#1 at slave addr 0x20
	fragment@57 {
		target = <&sx1504_1_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_20_pins>;
		};
	};

	// Enable interrupts for a SX1504 on I2C#0 at slave addr 0x21
	fragment@58 {
		target = <&sx1504_0_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_21_pins>;
		};
	};

	// Enable interrupts for a SX1504 on I2C#1 at slave addr 0x21
	fragment@59 {
		target = <&sx1504_1_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_21_pins>;
		};
	};

	// Enable interrupts for a SX1505 on I2C#0 at slave addr 0x20
	fragment@60 {
		target = <&sx1505_0_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_20_pins>;
		};
	};

	// Enable interrupts for a SX1505 on I2C#1 at slave addr 0x20
	fragment@61 {
		target = <&sx1505_1_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_20_pins>;
		};
	};

	// Enable interrupts for a SX1505 on I2C#0 at slave addr 0x21
	fragment@62 {
		target = <&sx1505_0_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_21_pins>;
		};
	};

	// Enable interrupts for a SX1505 on I2C#1 at slave addr 0x21
	fragment@63 {
		target = <&sx1505_1_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_21_pins>;
		};
	};

	// Enable interrupts for a SX1506 on I2C#0 at slave addr 0x20
	fragment@64 {
		target = <&sx1506_0_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_20_pins>;
		};
	};

	// Enable interrupts for a SX1506 on I2C#1 at slave addr 0x20
	fragment@65 {
		target = <&sx1506_1_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_20_pins>;
		};
	};

	// Enable interrupts for a SX1507 on I2C#0 at slave addr 0x3E
	fragment@66 {
		target = <&sx1507_0_3E>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_3E_pins>;
		};
	};

	// Enable interrupts for a SX1507 on I2C#1 at slave addr 0x3E
	fragment@67 {
		target = <&sx1507_1_3E>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_3E_pins>;
		};
	};

	// Enable interrupts for a SX1507 on I2C#0 at slave addr 0x3F
	fragment@68 {
		target = <&sx1507_0_3F>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_3F_pins>;
		};
	};

	// Enable interrupts for a SX1507 on I2C#1 at slave addr 0x3F
	fragment@69 {
		target = <&sx1507_1_3F>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_3F_pins>;
		};
	};

	// Enable interrupts for a SX1507 on I2C#0 at slave addr 0x70
	fragment@70 {
		target = <&sx1507_0_70>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_70_pins>;
		};
	};

	// Enable interrupts for a SX1507 on I2C#1 at slave addr 0x70
	fragment@71 {
		target = <&sx1507_1_70>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_70_pins>;
		};
	};

	// Enable interrupts for a SX1507 on I2C#0 at slave addr 0x71
	fragment@72 {
		target = <&sx1507_0_71>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_71_pins>;
		};
	};

	// Enable interrupts for a SX1507 on I2C#1 at slave addr 0x71
	fragment@73 {
		target = <&sx1507_1_71>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_71_pins>;
		};
	};

	// Enable interrupts for a SX1508 on I2C#0 at slave addr 0x20
	fragment@74 {
		target = <&sx1508_0_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_20_pins>;
		};
	};

	// Enable interrupts for a SX1508 on I2C#1 at slave addr 0x20
	fragment@75 {
		target = <&sx1508_1_20>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_20_pins>;
		};
	};

	// Enable interrupts for a SX1508 on I2C#0 at slave addr 0x21
	fragment@76 {
		target = <&sx1508_0_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_21_pins>;
		};
	};

	// Enable interrupts for a SX1508 on I2C#1 at slave addr 0x21
	fragment@77 {
		target = <&sx1508_1_21>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_21_pins>;
		};
	};

	// Enable interrupts for a SX1508 on I2C#0 at slave addr 0x22
	fragment@78 {
		target = <&sx1508_0_22>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_22_pins>;
		};
	};

	// Enable interrupts for a SX1508 on I2C#1 at slave addr 0x22
	fragment@79 {
		target = <&sx1508_1_22>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_22_pins>;
		};
	};

	// Enable interrupts for a SX1508 on I2C#0 at slave addr 0x23
	fragment@80 {
		target = <&sx1508_0_23>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_23_pins>;
		};
	};

	// Enable interrupts for a SX1508 on I2C#1 at slave addr 0x23
	fragment@81 {
		target = <&sx1508_1_23>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_23_pins>;
		};
	};

	// Enable interrupts for a SX1509 on I2C#0 at slave addr 0x3E
	fragment@82 {
		target = <&sx1509_0_3E>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_3E_pins>;
		};
	};

	// Enable interrupts for a SX1509 on I2C#1 at slave addr 0x3E
	fragment@83 {
		target = <&sx1509_1_3E>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_3E_pins>;
		};
	};

	// Enable interrupts for a SX1509 on I2C#0 at slave addr 0x3F
	fragment@84 {
		target = <&sx1509_0_3F>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_3F_pins>;
		};
	};

	// Enable interrupts for a SX1509 on I2C#1 at slave addr 0x3F
	fragment@85 {
		target = <&sx1509_1_3F>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_3F_pins>;
		};
	};

	// Enable interrupts for a SX1509 on I2C#0 at slave addr 0x70
	fragment@86 {
		target = <&sx1509_0_70>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_70_pins>;
		};
	};

	// Enable interrupts for a SX1509 on I2C#1 at slave addr 0x70
	fragment@87 {
		target = <&sx1509_1_70>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_70_pins>;
		};
	};

	// Enable interrupts for a SX1509 on I2C#0 at slave addr 0x71
	fragment@88 {
		target = <&sx1509_0_71>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_0_71_pins>;
		};
	};

	// Enable interrupts for a SX1509 on I2C#1 at slave addr 0x71
	fragment@89 {
		target = <&sx1509_1_71>;
		__dormant__ {
			interrupt-parent = <&gpio>;
			interrupt-controller;
			pinctrl-names = "default";
			pinctrl-0 = <&sx150x_1_71_pins>;
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x20
        // Configure as a input with no pull-up/down
	fragment@90 {
		target = <&gpio>;
		__dormant__ {
			sx150x_0_20_pins: sx150x_0_20_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-0-20-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x20
        // Configure as a input with no pull-up/down
	fragment@91 {
		target = <&gpio>;
		__dormant__ {
			sx150x_1_20_pins: sx150x_1_20_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-1-20-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x21
        // Configure as a input with no pull-up/down
	fragment@92 {
		target = <&gpio>;
		__dormant__ {
			sx150x_0_21_pins: sx150x_0_21_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-0-21-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x21
        // Configure as a input with no pull-up/down
	fragment@93 {
		target = <&gpio>;
		__dormant__ {
			sx150x_1_21_pins: sx150x_1_21_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-1-21-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x22
        // Configure as a input with no pull-up/down
	fragment@94 {
		target = <&gpio>;
		__dormant__ {
			sx150x_0_22_pins: sx150x_0_22_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-0-22-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x22
        // Configure as a input with no pull-up/down
	fragment@95 {
		target = <&gpio>;
		__dormant__ {
			sx150x_1_22_pins: sx150x_1_22_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-1-22-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x23
        // Configure as a input with no pull-up/down
	fragment@96 {
		target = <&gpio>;
		__dormant__ {
			sx150x_0_23_pins: sx150x_0_23_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-0-23-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x23
        // Configure as a input with no pull-up/down
	fragment@97 {
		target = <&gpio>;
		__dormant__ {
			sx150x_1_23_pins: sx150x_1_23_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-1-23-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x3E
        // Configure as a input with no pull-up/down
	fragment@98 {
		target = <&gpio>;
		__dormant__ {
			sx150x_0_3E_pins: sx150x_0_3E_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-0-3E-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x3E
        // Configure as a input with no pull-up/down
	fragment@99 {
		target = <&gpio>;
		__dormant__ {
			sx150x_1_3E_pins: sx150x_1_3E_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-1-3E-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x3F
        // Configure as a input with no pull-up/down
	fragment@100 {
		target = <&gpio>;
		__dormant__ {
			sx150x_0_3F_pins: sx150x_0_3F_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-0-3F-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x3F
        // Configure as a input with no pull-up/down
	fragment@101 {
		target = <&gpio>;
		__dormant__ {
			sx150x_1_3F_pins: sx150x_1_3F_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-1-3F-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x70
        // Configure as a input with no pull-up/down
	fragment@102 {
		target = <&gpio>;
		__dormant__ {
			sx150x_0_70_pins: sx150x_0_70_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-0-70-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x70
        // Configure as a input with no pull-up/down
	fragment@103 {
		target = <&gpio>;
		__dormant__ {
			sx150x_1_70_pins: sx150x_1_70_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-1-70-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x71
        // Configure as a input with no pull-up/down
	fragment@104 {
		target = <&gpio>;
		__dormant__ {
			sx150x_0_71_pins: sx150x_0_71_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-0-71-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	// Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x71
        // Configure as a input with no pull-up/down
	fragment@105 {
		target = <&gpio>;
		__dormant__ {
			sx150x_1_71_pins: sx150x_1_71_pins {
				brcm,pins = <0>;  /* overwritten by sx150x-1-71-int-gpio parameter */
				brcm,function = <0>;
				brcm,pull = <0>;
			};
		};
	};

	__overrides__ {
		sx1501-0-20          = <0>,"+0+2";
		sx1501-1-20          = <0>,"+1+3";
		sx1501-0-21          = <0>,"+0+4";
		sx1501-1-21          = <0>,"+1+5";
		sx1502-0-20          = <0>,"+0+6";
		sx1502-1-20          = <0>,"+1+7";
		sx1502-0-21          = <0>,"+0+8";
		sx1502-1-21          = <0>,"+1+9";
		sx1503-0-20          = <0>,"+0+10";
		sx1503-1-20          = <0>,"+1+11";
		sx1504-0-20          = <0>,"+0+12";
		sx1504-1-20          = <0>,"+1+13";
		sx1504-0-21          = <0>,"+0+14";
		sx1504-1-21          = <0>,"+1+15";
		sx1505-0-20          = <0>,"+0+16";
		sx1505-1-20          = <0>,"+1+17";
		sx1505-0-21          = <0>,"+0+18";
		sx1505-1-21          = <0>,"+1+19";
		sx1506-0-20          = <0>,"+0+20";
		sx1506-1-20          = <0>,"+1+21";
		sx1507-0-3E          = <0>,"+0+22";
		sx1507-1-3E          = <0>,"+1+23";
		sx1507-0-3F          = <0>,"+0+24";
		sx1507-1-3F          = <0>,"+1+25";
		sx1507-0-70          = <0>,"+0+26";
		sx1507-1-70          = <0>,"+1+27";
		sx1507-0-71          = <0>,"+0+28";
		sx1507-1-71          = <0>,"+1+29";
		sx1508-0-20          = <0>,"+0+30";
		sx1508-1-20          = <0>,"+1+31";
		sx1508-0-21          = <0>,"+0+32";
		sx1508-1-21          = <0>,"+1+33";
		sx1508-0-22          = <0>,"+0+34";
		sx1508-1-22          = <0>,"+1+35";
		sx1508-0-23          = <0>,"+0+36";
		sx1508-1-23          = <0>,"+1+37";
		sx1509-0-3E          = <0>,"+0+38";
		sx1509-1-3E          = <0>,"+1+39";
		sx1509-0-3F          = <0>,"+0+40";
		sx1509-1-3F          = <0>,"+1+41";
		sx1509-0-70          = <0>,"+0+42";
		sx1509-1-70          = <0>,"+1+43";
		sx1509-0-71          = <0>,"+0+44";
		sx1509-1-71          = <0>,"+1+45";
		sx1501-0-20-int-gpio = <0>,"+46+90",  <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1501_0_20>,"interrupts:0";
		sx1501-1-20-int-gpio = <0>,"+47+91",  <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1501_1_20>,"interrupts:0";
		sx1501-0-21-int-gpio = <0>,"+48+92",  <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1501_0_21>,"interrupts:0";
		sx1501-1-21-int-gpio = <0>,"+49+93",  <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1501_1_21>,"interrupts:0";
		sx1502-0-20-int-gpio = <0>,"+50+90",  <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1502_0_20>,"interrupts:0";
		sx1502-1-20-int-gpio = <0>,"+51+91",  <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1502_1_20>,"interrupts:0";
		sx1502-0-21-int-gpio = <0>,"+52+92",  <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1502_0_21>,"interrupts:0";
		sx1502-1-21-int-gpio = <0>,"+53+93",  <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1502_1_21>,"interrupts:0";
		sx1503-0-20-int-gpio = <0>,"+54+90",  <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1503_0_20>,"interrupts:0";
		sx1503-1-20-int-gpio = <0>,"+55+91",  <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1503_1_20>,"interrupts:0";
		sx1504-0-20-int-gpio = <0>,"+56+90",  <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1504_0_20>,"interrupts:0";
		sx1504-1-20-int-gpio = <0>,"+57+91",  <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1504_1_20>,"interrupts:0";
		sx1504-0-21-int-gpio = <0>,"+58+92",  <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1504_0_21>,"interrupts:0";
		sx1504-1-21-int-gpio = <0>,"+59+93",  <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1504_1_21>,"interrupts:0";
		sx1505-0-20-int-gpio = <0>,"+60+90",  <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1505_0_20>,"interrupts:0";
		sx1505-1-20-int-gpio = <0>,"+61+91",  <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1505_1_20>,"interrupts:0";
		sx1505-0-21-int-gpio = <0>,"+62+92",  <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1505_0_21>,"interrupts:0";
		sx1505-1-21-int-gpio = <0>,"+63+93",  <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1505_1_21>,"interrupts:0";
		sx1506-0-20-int-gpio = <0>,"+64+90",  <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1506_0_20>,"interrupts:0";
		sx1506-1-20-int-gpio = <0>,"+65+91",  <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1506_1_20>,"interrupts:0";
		sx1507-0-3E-int-gpio = <0>,"+66+98",  <&sx150x_0_3E_pins>,"brcm,pins:0", <&sx1507_0_3E>,"interrupts:0";
		sx1507-1-3E-int-gpio = <0>,"+67+99",  <&sx150x_1_3E_pins>,"brcm,pins:0", <&sx1507_1_3E>,"interrupts:0";
		sx1507-0-3F-int-gpio = <0>,"+68+100", <&sx150x_0_3F_pins>,"brcm,pins:0", <&sx1507_0_3F>,"interrupts:0";
		sx1507-1-3F-int-gpio = <0>,"+69+101", <&sx150x_1_3F_pins>,"brcm,pins:0", <&sx1507_1_3F>,"interrupts:0";
		sx1507-0-70-int-gpio = <0>,"+60+102", <&sx150x_0_70_pins>,"brcm,pins:0", <&sx1507_0_70>,"interrupts:0";
		sx1507-1-70-int-gpio = <0>,"+71+103", <&sx150x_1_70_pins>,"brcm,pins:0", <&sx1507_1_70>,"interrupts:0";
		sx1507-0-71-int-gpio = <0>,"+72+104", <&sx150x_0_71_pins>,"brcm,pins:0", <&sx1507_0_71>,"interrupts:0";
		sx1507-1-71-int-gpio = <0>,"+73+105", <&sx150x_1_71_pins>,"brcm,pins:0", <&sx1507_1_71>,"interrupts:0";
		sx1508-0-20-int-gpio = <0>,"+74+90",  <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1508_0_20>,"interrupts:0";
		sx1508-1-20-int-gpio = <0>,"+75+91",  <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1508_1_20>,"interrupts:0";
		sx1508-0-21-int-gpio = <0>,"+76+92",  <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1508_0_21>,"interrupts:0";
		sx1508-1-21-int-gpio = <0>,"+77+93",  <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1508_1_21>,"interrupts:0";
		sx1508-0-22-int-gpio = <0>,"+78+94",  <&sx150x_0_22_pins>,"brcm,pins:0", <&sx1508_0_22>,"interrupts:0";
		sx1508-1-22-int-gpio = <0>,"+79+95",  <&sx150x_1_22_pins>,"brcm,pins:0", <&sx1508_1_22>,"interrupts:0";
		sx1508-0-23-int-gpio = <0>,"+80+96",  <&sx150x_0_23_pins>,"brcm,pins:0", <&sx1508_0_23>,"interrupts:0";
		sx1508-1-23-int-gpio = <0>,"+81+97",  <&sx150x_1_23_pins>,"brcm,pins:0", <&sx1508_1_23>,"interrupts:0";
		sx1509-0-3E-int-gpio = <0>,"+82+98",  <&sx150x_0_3E_pins>,"brcm,pins:0", <&sx1509_0_3E>,"interrupts:0";
		sx1509-1-3E-int-gpio = <0>,"+83+99",  <&sx150x_1_3E_pins>,"brcm,pins:0", <&sx1509_1_3E>,"interrupts:0";
		sx1509-0-3F-int-gpio = <0>,"+84+100", <&sx150x_0_3F_pins>,"brcm,pins:0", <&sx1509_0_3F>,"interrupts:0";
		sx1509-1-3F-int-gpio = <0>,"+85+101", <&sx150x_1_3F_pins>,"brcm,pins:0", <&sx1509_1_3F>,"interrupts:0";
		sx1509-0-70-int-gpio = <0>,"+86+102", <&sx150x_0_70_pins>,"brcm,pins:0", <&sx1509_0_70>,"interrupts:0";
		sx1509-1-70-int-gpio = <0>,"+87+103", <&sx150x_1_70_pins>,"brcm,pins:0", <&sx1509_1_70>,"interrupts:0";
		sx1509-0-71-int-gpio = <0>,"+88+104", <&sx150x_0_71_pins>,"brcm,pins:0", <&sx1509_0_71>,"interrupts:0";
		sx1509-1-71-int-gpio = <0>,"+89+105", <&sx150x_1_71_pins>,"brcm,pins:0", <&sx1509_1_71>,"interrupts:0";
	};
};