3
0
mirror of https://github.com/Qortal/Brooklyn.git synced 2025-01-31 07:12:18 +00:00
Brooklyn/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
Raziel K. Crowe 8b701010de mempow update
2022-09-13 23:14:27 +05:00

201 lines
3.5 KiB
Plaintext

/dts-v1/;
#include "bcm2709.dtsi"
#include "bcm2709-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
#include "bcm283x-rpi-csi1-2lane.dtsi"
#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
/ {
compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
model = "Raspberry Pi 2 Model B";
};
&gpio {
/*
* Taken from rpi_SCH_2b_1p2_reduced.pdf and
* the official GPU firmware DT blob.
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "ID_SDA",
"ID_SCL",
"SDA1",
"SCL1",
"GPIO_GCLK",
"GPIO5",
"GPIO6",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"GPIO12",
"GPIO13",
/* Serial port */
"TXD0",
"RXD0",
"GPIO16",
"GPIO17",
"GPIO18",
"GPIO19",
"GPIO20",
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"GPIO26",
"GPIO27",
"SDA0",
"SCL0",
"NC", /* GPIO30 */
"LAN_RUN",
"CAM_GPIO1",
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"PWR_LOW_N",
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"USB_LIMIT",
"NC", /* GPIO39 */
"PWM0_OUT",
"CAM_GPIO0",
"SMPS_SCL",
"SMPS_SDA",
"ETH_CLK",
"PWM1_OUT",
"HDMI_HPD_N",
"STATUS_LED",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
spi0_pins: spi0_pins {
brcm,pins = <9 10 11>;
brcm,function = <4>; /* alt0 */
};
spi0_cs_pins: spi0_cs_pins {
brcm,pins = <8 7>;
brcm,function = <1>; /* output */
};
i2c0_pins: i2c0 {
brcm,pins = <0 1>;
brcm,function = <4>;
};
i2c1_pins: i2c1 {
brcm,pins = <2 3>;
brcm,function = <4>;
};
i2s_pins: i2s {
brcm,pins = <18 19 20 21>;
brcm,function = <4>; /* alt0 */
};
audio_pins: audio_pins {
brcm,pins = <40 45>;
brcm,function = <4>;
brcm,pull = <0>;
};
};
&uart0 {
status = "okay";
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
spidev0: spidev@0{
compatible = "spidev";
reg = <0>; /* CE0 */
#address-cells = <1>;
#size-cells = <0>;
spi-max-frequency = <125000000>;
};
spidev1: spidev@1{
compatible = "spidev";
reg = <1>; /* CE1 */
#address-cells = <1>;
#size-cells = <0>;
spi-max-frequency = <125000000>;
};
};
&i2c0if {
clock-frequency = <100000>;
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <100000>;
};
&i2c2 {
clock-frequency = <100000>;
};
&i2s {
pinctrl-names = "default";
pinctrl-0 = <&i2s_pins>;
};
&leds {
act_led: led-act {
label = "led0";
linux,default-trigger = "mmc0";
gpios = <&gpio 47 0>;
};
pwr_led: led-pwr {
label = "led1";
linux,default-trigger = "input";
gpios = <&gpio 35 0>;
};
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&vchiq {
pinctrl-names = "default";
pinctrl-0 = <&audio_pins>;
};
&cam1_reg {
gpio = <&gpio 41 GPIO_ACTIVE_HIGH>;
};
cam0_reg: &cam_dummy_reg {
};
/ {
__overrides__ {
audio = <&chosen>,"bootargs{on='snd_bcm2835.enable_headphones=1 snd_bcm2835.enable_hdmi=1',off='snd_bcm2835.enable_headphones=0 snd_bcm2835.enable_hdmi=0'}";
act_led_gpio = <&act_led>,"gpios:4";
act_led_activelow = <&act_led>,"gpios:8";
act_led_trigger = <&act_led>,"linux,default-trigger";
pwr_led_gpio = <&pwr_led>,"gpios:4";
pwr_led_activelow = <&pwr_led>,"gpios:8";
pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
};
};