files for fixing titan sound.

cmdline.txt

@@ -0,0 +1 @@
+console=serial0,115200 console=tty1 root=PARTUUID=c17010bc-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait snd-bcm2835.enable_compat_alsa=1

config.txt

@@ -0,0 +1,93 @@
+# BrooklynR NXT Hybrid, The Blockchain Linux 5.20.x by Scare Crow
+# ===============================================================
+#
+# * Brooklyn NXT Sinclair current 5.20.14 
+# * BrooklynR NXT QortalOS Community 5.16.x LTS-LE
+# * V1.2.3 BrooklynR NXT GUI 5.16.x is based on GNOME community code
+# * V1.2 BrooklynR NXT GUI 5.16.x is based on LXQT community code
+# * V 1.0 is based off a variety of Desktops with Brooklyn The Moose 5.12.6
+# * V 1.0 Jaymen is based on headless R Kernel 5.13.10 LTS
+# * RussCade 1.0 is based on optimized BrooklynR for Qortal minting and game emulators
+# * V1.1 XFCE is based on  Brooklyn Jackwagon 5.12.10 LTS
+# * V1.1 MATE-LXDE is based on Brookltn Plumbus 5.12.10 LTS
+#
+# =======================================================
+# If this has helped you in any way then throw me some
+# LTC for R&D or a few gallons of petrol mixed with booze 
+# Personal LTC: LL5pThYz8z5zqjJVgnCkwHHWhmb72DtZpY
+# Personal QORT: QdiGEQEr17Jho5RZuhNhzPUX671DqKq3Xt
+#
+# -/ Scare Crowe
+#
+# Before I forget, fuck you T3Q. I hope you eat shit and die.
+#
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+#hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+#dtparam=i2c_arm=on
+#dtparam=i2s=on
+#dtparam=spi=on
+
+# Uncomment this to enable infrared communication.
+#dtoverlay=gpio-ir,gpio_pin=17
+#dtoverlay=gpio-ir-tx,gpio_pin=18
+
+# Additional overlays and parameters are documented /boot/overlays/README
+#
+kernel=vmlinuz-5.60.12LTS-Sinclair_Titan+
+over_voltage=2
+arm_freq=1750
+#arm_boost=1
+#
+[pi4]
+max_framebuffers=2
+
+[all]
+dtoverlay=vc4-fkms-v3d
+gpu_mem=512
+gpu_freq=600
+dtparam=audio=on
+   hdmi_group=2
+   hdmi_mode=82